P102 3-MOTOR POWER DISTRIBUTION BOARD [BUY NOW] £ 25.00 Incl VAT | |
The P102 has been developed from our very popular P92 Power Distribution Board for models using three motors. This provides three separately-fused groups @6V - 15V input voltage (maximum current is 15A per group) PLUS a regulated 5v 'BEC' for Rx supply. Includes TWO FULL sets of fuses, a universal servo/BEC lead and 14AWG silicon cable. Board size is 64mm x 70mm; unit is uncased. Screwdriver connection. 6v BEC version also available |
|
P103 PARALLEL POWER BOARD [BUY NOW] £ 14.50 Incl VAT | |
This simple little board has a dual 20A Schottky diode and heat-sink. It allows the safe use of two equally-rated batteries, wired in parallel for increased capacity and therefore longer running times, by eliminating the risk of dangerous "back-charging" from one battery to the other. |
|
P19 BEC 1A BATTERY ELIMINATOR [BUY NOW] £ 9.00 Incl VAT | |
Eliminates the need for receiver battery pack in your model. For operation on 6 to 12 Volt main power pack. 1 Amp output capability. Size - 34mm x 24.5mm x 16mm. Requires separate ON/OFF switch.
6v output version also available |
|
P22 SERVO SWINGER [BUY NOW] £ 12.00 Incl VAT | |
Simple off-air servo driver; uses a separate battery box with 4 x AA alkaline or NiCad/NiMH cells. A very useful item for testing and setting up servos, RC switchers and electronic speed controllers without a receiver or transmitter; you'll soon wonder how you managed without it. Battery box, clip and servo connector are supplied. Batteries not included. |
|
P38 RF SIGNAL METER KIT [BUY NOW] £ 13.00 (Kit only) Incl VAT | |
This unit clips onto the transmitter aerial and monitors the actual transmitted RF power. Can be used with AM or FM transmitters operating on 27MHz, 35MHz or 40MHz. Kit only. Full building and setting-up instructions and diagrams are included (the transmitter is not!) |
|
P59 R/C MASTER KIT [BUY NOW] £ 30.00 (Kit only) Incl VAT | |
PIC microcomputer-based; tests and exercises servos, switchers or speed controllers; checks the centre-stick timing value of your transmitter sticks; run-in motors via ESC. LED bar-graph output display. Powered by a Rx pack (4.8 Volts) or 4 x 1.5v alkaline cells (batteries not included). Available in kit form only. Full instructions, drawings and full-size case cut-out template are included. |
|
P92 POWER DISTRIBUTION BOARD [BUY NOW] £ 24.00 Incl VAT | |
The P92 Power Distribution Board provides a neat solution to "Rat's Nest" wiring when multiple units are installed in a R/C model boat. Two separately fused groups @ 6V - 12V input voltage PLUS a regulated 5v 'BEC' for Rx supply. Includes TWO FULL sets of fuses and a universal servo/BEC lead . Board size is 64mm x 70mm; unit is uncased. Screwdriver connection. 6v BEC version also available |
|
P95 INDICATOR FUSE BOARDS [BUY NOW] £ 5.00; £ 10.00; £ 15.00 (All Incl VAT) | |
Fuse-holder with screw-terminal connections. Bi-colour LED gives a visual indication of the direction of current from the ESC. Maximum current rating is 25A per board. Single, twin and triple circuit versions available. Supplied with two blade fuses per board (10A and 15A). |
|
P99
5V IN-LINE REGULATOR [BUY NOW]
£ 6.50 Incl VAT | |
This has been produced to allow many of the recent micro-processor controlled ACTion units to be connected to a receiver which is running from a 5-cell pack or 6v SLA battery. These units can be damaged if run at voltages >6.5v, so P99 will regulate the feed to them at 5v while still permitting full power to the other devices e.g. servos.
|
|